Hi, crafty friends! Today is Mother’s Day in Norway, and I probably should have thought ahead enough to make a Mother’s Day card to share today, but I’m not always a good thinkaheader and have a birthday card to share instead. My design is pretty generic, though, and it would be easy to swap out “birthday” for “Mother’s Day”. I even think the color scheme is perfect for mother’s day.

So many things went wrong in the creation of this card, but I fixed/covered up most of my mistakes and I’m pretty happy with the end result. I started by stamping birthday from the All the birthdays stamp set from Concord & 9th onto an A6 panel of Stamper’s Select White cardstock from Papertrey Ink, as well as onto a piece of Nectar cardstock from Concord & 9th that was large enough to cover the shaker area. I didn’t want to stamp it directly onto the card base, that would have made it harder to line up. More on that later. So far, so good, right? I then die cut the HAPPY from the Happy Birthday words dies from Kristina Werner into my white panel, and kept the counters of the A and the Ps to put back in later. Things were still going according to plan. There’s a small asterisk looking stamp in the All the birthdays stamp set. I wanted to stamp that randomly across my white panel and pulled out an acrylic block. We used to stamp with acrylic blocks all the time before the Misti was invented. I’m not a ding dong, surely, I’m capable of stamping this tiny stamp a few times with an acrylic block without messing up, right? Turns out I AM a ding dong and royally messed up on the Eucalyptus colored asterisk above the A and P. Pretty much in the middle of the card, isn’t that typical? I knew I was going to add sequins, and I could strategically place one to cover up my boo boo. I cut off 3/16″ on all sides to allow the card base color to work as a frame once the card was complete.

I then adhered a piece of acetate behind my letters, glued the counters (interior pieces of the letters) back in onto the acetate, flipped the panel over and added tons of foam tape around the shaker window pretty close to the window, even putting tiny strips behind the counters of the Ps, before putting a few sequins from Altenew into the shaker well before sealing it shut with another piece of acetate. I made sure to add the sequins the right side up. That was not a good idea, but I didn’t realize at the time and adhered my shaker piece onto the stamped piece of Nectar cardstock to line up the stamping on the two pieces. The problem with the sequins all facing the same way is that once they shook around, they clumped together like stacks and were pretty much impossible to separate by flicking the card. The other mistake? Adding the foam tape so close to the letters and behind the counters, my sequins didn’t really have a chance to move much. I had adhered everything to the card base at this point.

I’m not shy with glue when adhering things, but I was able to slide a thin 6″ steel ruler under my shaker panel and basically used it as a saw to cut it away from the card base, cutting horizontally so I would preserve the card base as well as I could. I didn’t have another sheet of Nectar cardstock to create a new A6 card base, so this was the way to fix it. I then pulled off the nectar piece with the stamping, then the back acetate piece, which took with it a few of the small pieces of foam tape that were in the way anyway, and then I emptied out the sequins, made sure there were no sticky pieces left behind, put sequins back into the now rectangular shaker window, this time randomly with some upside down and some right side up – and I added way more sequins too, before sealing it shut with a new piece of acetate. The piece of Nectar cardstock I’d stamped on initially had crease lines after being pulled off, so I had to restamp birthday on a new piece of Nectar. Evidently, I didn’t put the stamp into the Misti the same way as I had the first time, because the new stamping wouldn’t really line up with the old stamping – part of the nature of photopolymer stamps, they’re soft and can be curved. The loops on the b and h don’t perfectly line up with the stamping on the white panel the way they initially did, but this is me embracing imperfection, I wasn’t redoing the white panel too.

I adhered my shaker panel to the card base and cut a couple of additional white panels to put on the inside of the card. This means I have a white panel to write my personal message, the card is a little sturdier because it’s now thicker, and the piece I adhered on the back of the front covers up the fact that I could actually see through parts of the card base after my little sawing earlier. Not shy about glue, remember? Yeah, the glue does its job, and I tore parts of it down to almost printer paper thickness. I added sequins to the front of the card (one covering up my stamping mishap) and I was done. At least I thought so… I was happy with the card, but then noticed as I was writing up the blog post for Papiria that the counter of the second P had slipped a little and wasn’t in the right spot anymore. It was bugging me. It was *really* bugging me, so I peeled it off, die cut a new one that I adhered in the right spot and took a couple of new photos. You can still see the droopy counter in the first two photos here, but that’s my card. I got there in the end.